Expert Answers about Land Rover
- Will Curt Echo Brake Controller # C51180 Fit 2017 Land Rover Discovery with Towing Package
- Yes, the Curt Echo Brake controller # C51180 that you referenced does fit your 2017 Land Rover Discovery that has a factory 7-way. Basically this controller fits any vehicle that has a fully functional 7-way. As long as the trailer lighting circuits are functioning and the 12 volt accessory circuit is active this controller will work great.
view full answer... - Troubleshooting LED Lighting on Trailer Not Working Behind a 2006 Land Rover LR3
- Unfortunately, it sounds like there may be an issue with either the wiring or the control module on your 2006 Land Rover LR3. As you have tried the 7-Way to 4-Way/5-Way Trailer Adapter for Vehicles with Lamp-Out Sensors Towing Trailers with LEDs # C35FR as well as adding resistors with both failures to operate the lights. It only stands to reason the vehicle has something going on with it that it is not recognizing you have a trailer connected.
view full answer... - Hitch Recommendation For 2020 Land Rover Range Rover Sport
- The Curt hitches like part # C13243 for the 2020 Land Rover Range Rover Sport require the stabilization strap part # 18050 with accessories because the Land Rovers are not designed to handle a lot of tongue weight and accessories like bike racks are considered all tongue weight which puts a lot of leverage on the setup.
Both the Draw-Tite Hitch part # 75229 and the Curt hitch will be recessed under the bumper because they install exactly the same. I have attached a video snip showing...
view full answer... - Recommended Hitch Extender for Towing with a 2008 Range Rover
- Since hitch extenders like the 11" Roadmaster # RM-071 you show in your pictures reduces the weight rating of the hitch by 50% we typically recommend avoiding them as a solution. For your application we have ball mounts with extended shanks that don't reduce the weight capacity of your hitch and that's what I recommend going with.
For a long ball mount we have the Brophy Ball Mount # BM20 which has a 3/4" rise/2" drop and measures 13-1/4" from the center of the hitch pin hole to center...
view full answer... - Thule Snowpack Ski Carrier and Roof Rack for a 2016 Land Rover LR4
- I have a solution for you but you will need that part number you circled to find a replacement roof rack from Land Rover or online. We do not sell OEM parts. We do offer a roof rack that will fit your 2016 Land Rover LR4's factory installed tracks that run front to back. This rack is also compatible with the Thule SnowPack Extender Ski and Snowboard Carrier item # TH7325. It is the 2016 Land Rover LR4 Roof Rack by Rhino Rack. This Roof Rack Includes:
Rhino-Rack Vortex Aero Crossbars -...
view full answer... - Trailer Hitch and Wiring Recommendation for 2020 Land Rover Range Rover Sport
- The Draw Tite hitch part # 75229 is the hitch I recommend for your 2020 Land Rover Range Rover Sport as it has great towing capacities, is mostly hidden, and installs relatively easy. I attached an install video that will walk you through the entire install process as well as a picture that shows what it looks like installed as well.
For trailer wiring you'd then want the zero splice kit part # 119250KIT which installs without requiring you to cut into your factory wiring!
If you wanted...
view full answer... - Hitch Extender to Use with etrailer Cargo Carrier # e89974
- You didn't say how long of a hitch extender you need but the part # HE06 is 7 inches long and would help you get additional clearance for the etrailer cargo carrier part # e98874 to fold up like you are wanting. You should note that when you use a hitch extender like this you end up cutting the capacity of the hitch by 50 percent due to the increased leverage and movement created.
view full answer... - Availability Of Replacement Hardware For Curt Trailer Hitch Receiver 13456
- To get the mounting hardware to install the Curt Trailer hitch Receiver # 13456 you were looking at you will need to use Replacement Hardware Kit # RHK.
On the product page for the # RHK you will select Curt from the drop down menu and enter 13456 in the hitch item number field. This will get you all of the replacement hardware required to get the hitch installed.
I included videos for both of the products mentioned for you to take a look at.
view full answer... - 7-Way Tester Recommendation for a Land Rover with 7-Way and P3 Brake Controller
- Yes, we do offer a 7-way tester that will allow you to plug into the 7-way at the rear of your Land Rover to test all of the functions. For that you would want the part # C73NR.
view full answer... - Ground Clearance Difference Between 2015 Jeep Cherokee Latitude And Trailhawk
- I did some research on the 2015 Jeep Cherokee Latitude And Trailhawk with the same engine. From what I was able to find the Latitude is 5 ft 5.7 inches from the top of the roof to the ground and the Trailhawk is 5 ft 7.8 inches. This is assuming the same size tires, wheels, and suspension are being used on the vehicle. A difference in any of those components would certainly make a difference in the bumper height.
The Curt Trailer Hitch, part # C13172 is a fit for both models. This is...
view full answer... - What Material is Valterra Plumbing Roof Vent Made of
- The Valterra Plumbing Roof Vent # VA97ZR has a polypropylene construction. This is a thermoplastic polymer which is basically a fancy way of saying that it's essentially plastic.
view full answer... - Swing Away Hitch Adapter that Can be Used with Yakima OnRamp E-Bike Rack
- You can use the Yakima OnRamp part # Y36FR with the Yakima Swing Away adapter part # Y02483 that you referenced. This will give you additional clearance to fit past your rear mounted spare and will work great with your Priority Current and Gazelle e-bikes.
view full answer... - Does Valterra P-Trap D50-2215 Use Washer
- PVC Ptraps like the # D50-2215 do use a beveled cone washer when installing. When one of these leaks it can be just a matter of the nut not being tight enough or the washer needs replacing.
view full answer... - Do the Load Resistors in the Load Resistor Kit for LED Turn Signals Have + and - Markings
- No, there is not a positive (+) and negative (-) on the ends of the Load Resistor Kit for LED Turn Signals # DI34ZR. It does not matter which side connects to the positive and which to the ground.
I have included a couple wiring diagrams you can check out to help with installation.
view full answer... - Choosing Malone MegaSport or Yakima Rack and Roll Trailer for Hobie Tandem Island
- You will need the Malone MegaSport Kayak Trailer # MPG535 for your Hobie Tandem Island. The Yakima # Y08107 has the capability of handling the weight of the boat, and can be extended to handle the length with the # Y08109. What it doesn't have is the required crossbar spread.
The Hobie cradles require 67" spacing on center for installation. The Rack and Roll only has a 48" maximum crossbar spread so you won't be able to mount the cradles.
The Malone MegaSport has a crossbar spread of...
view full answer... - 7-Way Adapter Recommendation for Land Rover Towing Trailer with LED Taillights
- Adapters like the Curt part # C57003 are designed for use on vehicles that will show a "bulb out" error code if towing a trailer with LED taillights like what your 2014 Land Rover LR4 would have. This would would well for you if your trailer and vehicle has a 7-way and you are getting that error code.
view full answer... - How High Will The Curt Receiver Sit Once Installed On A 2020 Range Rover Sport
- Though we have yet to get the chance to install the Curt # C13243 on a 2020 Land Rover Range Rover Sport, we have done an install with the Draw-Tite # 75229 on a 2016.
When this was done, we got 13 inches from the ground to the inside top of the receiver, which should be very similar, if not the same, as installing the # C13243 on your 2020.
Determining the correct rise will then depend on how high the bottom of the trailer coupler is from the ground. You technically have plus or minus...
view full answer... - Does The Curt Trailer Hitch For A 2018 Land Rover Evoque Require Trimming To Install
- Yes, the Curt Trailer Hitch Receiver # C13128 would require trimming of both the heat shield and rear fascia in order to install.
view full answer... - Trailer Suspension Hanger Kit with the Most Lift for Tire Clearance Under the Trailer Bed
- The # APT4 Tandem-Axle Hanger Kit will provide about 4 inches of clearance from the center of the trailer axle to the bottom of the trailer frame, with no load on the axle. This is assuming that your axle tube is 3 inches diameter. If your axle tube is smaller the height will be sightly less. The curve of the springs you select will have some affect also.
I would recommend that you go with the APT5 hanger kit because all of the hangers are the same height and it will make it easier to...
view full answer... - Parts Needed To Install Brake Controller on a 2002 Land Rover Discovery II for a 2013 Lance Trailer
- You will need to hardwire in a brake controller on your 2002 Land Rover Discovery II. First you will need to install a 4-Way trailer wiring harness unless the vehicle already has one, # 119178KIT.
Next you will need a 4 and 7 way installation kit # ETBC7. This kit provides the 7-way, wiring, and accessories needed to install a brake controller on the vehicle. I have included some links that explain the ETBC7 installation. A 20 amp circuit breaker, included, would be used if you have 2...
view full answer...
Go To Results